Turn the ignition to the on position. The next step is to work under the hood;
Leave the key in the ignition.
How to reset maintenance light on toyota tacoma 2013. We have a 2008 tacoma here, so let me show you how that is done. How to reset oil maintenance required light on toyota tacoma. After an oil change, you should reset your maintenance required light on your toyota tacoma.
How do you reset the maintenance light on a 2013 toyota tacoma? Turn your ignition key to the 'acc' or 'lock' position. To reset the maintenance lamp turn the car key to on (not start), set your odometer on mileage (not trip a or b), then depress and hold the button that switches from odo and trip then turn key off.
Toyota recommends not to ignore the light and doing a series of inspections to prevent damages to the engine. While holding the trip meter reset nob, turn the ignition to 'on', but do not start your toyota tacoma. To turn off the check engine light in a toyota tacoma, press down and hold the car horn for about 30 seconds to drain any electricity from the vehicle’s capacitor.
The odometer should display the miles, not the trip meter. How to reset maintenance light toyota. Next, turn off the ignitionafter that, you’re gonna need to hold down the odo/ trip button and then turn the car on again without cranking the enginekeep press the odo/ trip button until the maintenance required light shuts off
For some models, this is the button used to switch from the odometer reading to the other two trip meters. How to reset maintenance light on toyota tacoma 2016. So today, i’m going to show you how to reset the maintenance light on your toyota tacoma.
The 2013 toyota tacoma is offered in a gasoline model. If playback doesn't begin shortly, try restarting your device. This reset should be done after changed the engine oil and filter according to the technical specifications relating toyota tacoma.
I just finished the oil change, and then now i’m back in the car, and we’re going to do the maintenance. Press the odo/trip button to display to trip a. This video shows you how to reset turn off the oil maintenance light (maint reqd) on a 2006 2007 2008 2009 2010 2011 2012 2013 toyota tacoma oil change.if it.
Reset maintenance required light in 2013 toyota tacoma. The first ever 60 second ceramic version. Toyota tacoma reset maint reqd light indicator.
Press and hold the trip meter reset nob (next to your toyota tacoma's odometer). To reset maintenance required light toyota tacoma and that can be made manually by use button on car dashboard. Hold this button for a while.
Turn the key on and hold the odometer button until it flashes all zeros. Reset is complete and you are done. Follow these steps to reset this light:
Turn the ignition to the off position. Put your key in the ignition and turn it to position one, which is the position right before starting the car. The light should then flash, beep, and then go out.
Hold down the trip odometer reset knob. To reset maintenance required light toyota tacoma and that can be made manually by use button on car dashboard. Continue pressing on the trip odometer reset knob until the odometer indicates 0000000 and the maintenance light.
Go to the odometer and press the odometer to the trip a position, then turn the key off. Turn the ignition to run (one position before starting engine). If your vehicle has an ignition button, press the start/stop button two times without step on the brake pedal.
Please follow the instructions below according to your vehicle trim level. You take the service of a toyota dealership for the oil change, they will reset maintenance light toyota for yourself. Continue to hold down the trip odometer reset button until “000000” miles appears on the display and the maintenance light turns off.
Once you have turned the key back off, make sure that you press the trip meter reset button to reset the maintenance required light. Turn the key back to on, while you are holding the button down you will notice the maintenance light blink and go out. Keep holding the odometer button for 10 seconds.
Wait to reconnect the battery. Continue pressing on the trip odometer reset knob until the odometer indicates 0000000 and the maintenance light. Push and hold the trip meter reset button on the dashboard, then turn the key to position two.
After performing the oil change the maintenance data will need to be reset. Press and hold odo/trip button and turn ignition to the “run” position. Hold down the trip odometer reset knob.
Hold the meter reset until the maint reqd light. Turn the ignition key off push the trip reset button and hold wile turning ignition on. If you know why a particular warning light is illuminated on your toyota tacoma’s dashboard, then just seeing it there as a constant reminder that you haven’t yet had the time to go to the.
There are 2 methods to reset the maintenance reminder on your toyota tacoma. On your 2013 toyota tacoma, to reset the maintenance light, first put your key in and turn it to the on position. Turn the ignition to the on position.
Ensure trip meter a reading is shown.