There will be small holes where the railing attaches to the wall, and a large panel missing where the floor of the deck attaches to the house. Start by making an outline on the siding where you want to position the ledger board.
The easiest and safest way to hang something from vinyl siding is to use a siding hook.
How to attach a deck to a house with aluminum siding. Anchor deck joists to the ledger with joist hangers, filling each hole with galvanized joist hanger nails rated for. Most hooks are stainless steel, so they won't corrode, and. What stops me is what to do about the holes it leaves in the aluminum siding.
This would be the easiest way is accepted by the buyer. Mark the top of the ledger: Mark the spot where you want the ledger to sit.
Any siding that has a flat back and is in full contact with the house along it’s width (carsiding, for instance) will take to being bolted through. Then cut away the siding. Remove enough of the siding so you can tuck flashing behind the siding above the ledger and allow it to overhang the siding below the ledger.
Snap the line along the wall about 3 out and cut the deck boards. Start by using plunge cuts across the top and bottom of the horizontal length of the ledger board, followed by the shorter vertical cuts for the ends using a cold chisel. I want to tear off the deck and replace it with stairs down to a patio.
“lap siding, shingles, shakes, vinyl, aluminum, fiber cement, and many others have a void between the back of the siding and the sheathing,” jonblakemore adds. Many of the same skills you learned working with vinyl will apply however there are some tricks that you should observe for best results. This way all the water that runs along the siding will clear bolted ledger/joist.
Here are the steps to take when installing a ledger on a home with siding: It slips into the groove between adjoining slats, and once it clicks into place, you can hang items as heavy as 12 pounds. If necessary, create spacers by attaching pieces of decking to the top side of the frame that goes against the house.
When nailing your vinyl z flashing to the house, be sure to nail every 12″ along the house with roofing nails. No flashing at all, and the vintyl was installed wrong too. A deck ledger board is used when attaching a deck to a house.
How to work with aluminum siding. Nail the z flashing over the top of the ledger. Add your starter sheet of siding.
You just drill 2 1/2 in. Slip flashing under the siding. If your siding is not beveled, you can simply screw the ledger tightly to it.
Use an inverted piece of cedar siding to create a flat surface for attaching the ledger over lap siding. By attaching a wood ledger to the framing through the brick veneer, the bvlz enables decks to be safely tied to the home without requiring the removal or. 14 oc = lots of waste
Another technique is for the post to remain attached only to the deck but the top rail to continue over the post top and butt up against the wall of the home. Use a water level to ensure the ledger length is level. You cut the siding to the height you need (measure twice) and then the punch creates small tabs that stick out from the siding.
Slip the siding up and around the door. “bolting the ledger to the face of this type of siding will not give a solid connection. Then lay the hook flat against the siding and pull down gently to ensure the hook is secure.
Make sure you have enough room to install flashing above the ledger board and allow for at least a ¾” space above the decking, preventing water from wicking upwards into wood siding. I have been helping a friend fix up his lake house, and this summer we replaced the front deck. You can bridge the inch gap between deck and house with the decking board no problem and there should be no visual difference between this or any other deck building method if done right.
Push the hook up under the siding, wiggling it from side to side if needed to accomplish this. More common and less problematic is to use a post that is attached only to the deck and therefore must withstand the load imposed on that railing span. Slide the bottom of the siding into the footer, being sure to leave enough space to allow for expansion.
Make the outline large enough to include space for the deck boards on top, the ledger and any trim boards on the sides. When working with aluminum siding you apply it to the home starting at the bottom of the house. It supports both the deck joists, as well as bolsters the framing of the deck.
Slide the end, that meets the corner, in the same way. One major problem was the rim joist, looked just like that. You may need to pry out the siding first.
Leave a gap of 1 inch or more between the the top of the ledger and the edge of the vinyl siding when you install the bottom run of siding, which usually goes on first. Slip the back flashing under the siding at least 3″ at the top and the sides.